Kurzweil PC3LE8 Specifications download pdf (Page 343)

Tutorials: Setup Mode

Basics Of Using Riffs

14-41

18. Lastly, lets change the Stop point for the horn riff so that it loops with no gaps. Press the RIFF1 soft

button at the bottom of the page to move to the RIFF1 page for zone 6. On the RIFF1 page, use the

cursor buttons to select the left most Stop field. The Stop field sets the bar number (within the riff’s

original sequence) that the riff should stop at. The Stop field also sets the loop point when Loop

parameter is set to Forever on the RIFF2 page. Our horn riff is set to loop forever (the default

setting.) With the left most Stop field selected, press 9 and then the Enter button on the

alphanumeric pad to select 9 for the Stop field bars value (see below.) Now the horn riff should

loop with no gaps.

AtthispointyoumaywanttoadjustthevolumeofthehornsprogramonthePAN‐VOLpage

(anEntryVolumeof100may beamorecomfortablevolumeforthehornsriff.)Youcanalsosee

howtheriffsoundswithdifferentprogramsbyselectingdifferentprogramsontheCH/PROG

page.

19. To finish, press the Exit button to the right of the display to exit the Setup Editor and save your

changes to this setup under a new ID#. SeeTheSetupEditorsectionatthebeginningofthis

chapterfordetailsonsavingwhenyouexittheSetupEditor.

Youmaywishtodisablesomecontrolsforzonesthatplayriffs.Forexample,

thezonewithour

hornriffrespondstothesustainpedal,butthisdoesn’tsoundgoodwhenweareusingthe

sustainpedalforthezonewiththepianoprogram.Todisablethesustainpedalforzone6,goto

theControllerspageforzone6,selectSWPedal1

fortheControllerfieldandselectNoneforthe 

OnControlandOffControlfields.

Therearemanypossiblewaystouseriffsinasetup.Forexampleinsteadoftriggeringriffsfrom

thePC3LE’spadsyoucouldtriggerriffsfromtheassignableswitches.Thiswouldleavethepads

availabletoplaydrum

programs.Totriggerriffsfromtheassignableswitches,gototheSetup

EditorControllerspageforthezonecontainingtheriffyouwishtotrigger.Next,selectaswitch,

suchasswitch2fortheControllerfield(thiscanbedonebyselectingtheControllerfield,

holdingtheEnterbuttonand

pressingthedesiredswitch.)Then,withDestTypesettoCtrl,set

theOnControlandOffControlfieldsto163and164,RiffOnandRiffOff.Lastly,insomecases

youwouldneedtodisableanyswitchesthatyouareusingthatarealreadyassignedtoother

functionsinotherzones.Forexample,

bydefaultwhenazoneiscreateditassignsswitch1to

mutethatzone(forexample,whenyoucreatedzone6inthistut o rial,switch1wassettomute

keyboardplaybackofzone6automaticallyonzone6’sControllerspage.)Also, manyfactory

setupsusethesetupMUTES

softbuttonwhichautomaticallyassignseachswitchtomuteits

correspondingzone(seeSetControlsZoneMutes(MUTES) on page 7‐66.)Sousingswitches1

and2totriggerriffsonzones4and5wouldrequiresettingtheOnControlandOffControlfields

toOFFforswitch1onzone1and

switch2onzone2(dothisbyentering0thenpressingEnter

onthealphanumericpadforeachofthesefields.)Doingthiswouldensurethatzones1and2

wontbemutedwhenusingswitches1and2.Youcouldtryrepeatingthistutorialandchanging

alltheriffs

tobetriggeredbytheassignableswitches.

1 2 ... 338 339 340 341 342 343 344 345 346 347 348 ... 378 379

Kurzweil PC3LE8 Specifications Page 343

Comments to this Manuals