Kurzweil SPS4-8 Datasheet Page 79
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Edit Setup Mode
The Zone-specic Parameters
8-13
The Foot Switch Parameters
There are four parameters that affect the behavior of the Foot Switch controller:
Destination
The Destination parameter determines the MIDI destination for the currently selected
controller in the currently selected Zone. For a list of the MIDI destinations and their
descriptions, see Destination on page 8-10.
Mode
The Mode parameter determines the switching action of the Foot Switch. You can set this
parameter either of two settings:
Momentary A momentary switch is one that is only in the “on”
state when it is pressed. As soon as you release the
switch, it goes into the “off ” state.
Toggled A toggled switch is one that maintains its state after
it is pressed. So, if the switch is currently in the
“off ” state, pressing it once will put it in the “on”
state. Pressing it again will put it back in the “off ”
state.
Pressing both Value buttons simultaneously will set this parameter to Toggled.
Entry State
The Entry State parameter determines the state of the Foot Switch that is sent as a MIDI
message when the current Setup is loaded. You can set this parameter to None, On, or Off.
Pressing both Value buttons simultaneously will set this parameter to None.
If Entry State is set to None, then when you load the current Setup, the Foot Switch will be
at whatever value corresponds to its current position. If you specify an Entry State, then a
MIDI controller message with this value will be sent when you load the current Setup.
Exit State
The Exit State parameter determines the state of the Foot Switch that is sent as a MIDI
message when the current Setup is exited. You can set this parameter to None, On, or Off.
Pressing both Value buttons simultaneously will set this parameter to None.
If Exit State is set to None, then when you close the current Setup, the Foot Switch will be
at whatever value corresponds to its current position. If you specify an Exit State, then a
MIDI controller message with this value will be sent when you close the current Setup.
- SAVE THESE INSTRUCTIONS 2
- IMPORTANT SAFETY INSTRUCTIONS 3
- Table of Contents 5
- Chapter 10 9
- Chapter 11 9
- Chapter 12 10
- Appendix A 10
- Appendix B 10
- Chapter 1 11
- Introduction 11
- Staying Current 12
- Do You Have Everything? 12
- Chapter 2 13
- Getting Started 13
- Start Up Details: 14
- The Rear Panel 14
- The USB Port 15
- The Audio In Jacks 15
- The DC Power Jack 15
- Left and Right 16
- Audio Outputs 16
- Audio Inputs 16
- Connecting Pedals 18
- Connecting a Control Pedal 19
- SP4 Module 20
- Module SP4 20
- MIDI Controller 21
- Connecting MIDI 22
- Chapter 3 23
- Features of the SPS4 23
- Pitch Touchpad 24
- (on left cheekblock) 24
- Mod Slider 24
- (on front panel) 24
- Program Button 25
- Setup Button 25
- Edit Setup Button 25
- Global Button 25
- Save Button 25
- Split (Zone 1) Button 26
- Layer (Zone 2) Button 26
- Shift Button 26
- The Control Knob 27
- Display and Value Buttons 28
- Chan / Param Buttons 28
- Object Select Buttons 29
- Bank Select Button 30
- Group Select Buttons 30
- Sound Select Buttons 30
- Double Button Presses 31
- Jump Value 32
- Jump Parameter 32
- MIDI Program Change 32
- Chapter 4 35
- Terminology 35
- Chapter 5 37
- The Operating Modes 37
- Setup Mode 38
- Edit Setup Mode 38
- Global Mode 39
- System Mode 39
- Functions 40
- MIDI Program Change Function 41
- Demo Function 42
- Chapter 6 43
- Program Mode 43
- Table of Programs 44
- Selection 45
- Group Sound 46
- Alphanumeric Data Entry 47
- Transposition 48
- The Split Function 49
- The Layer Function 51
- Saving in Program Mode 52
- Chapter 7 55
- Table of Setups 56
- About Zones 59
- Saving in Setup Mode 65
- Chapter 8 67
- The Parameters of a Setup 68
- The Zone-specic Parameters 70
- MIDI Bank 71
- MIDI Program 72
- Bank Mode 73
- Zone Status 73
- Entry Program Change 73
- Aux Send Level 74
- Transpose 74
- Entry Pan 74
- Entry Volume 74
- Low Velocity 74
- High Velocity 75
- High Key 75
- Bend Range Down 75
- Bend Range Up 75
- The Foot Switch Parameters 79
- About Auxiliary Effects 80
- Common Parameters 80
- Chapter 9 83
- The Global Parameters 85
- FX Select (FXSel) 86
- Channel Enable (ChanEn) 86
- Destination (Dest) 86
- Bank Select (BankSel) 87
- Program Change (ProgChg) 87
- Sysex ID 88
- The “Hard Reset?” Dialogue 89
- The “Save All?” Dialogue 89
- The “Load All?” Dialogue 90
- Buttons in System Mode 92
- Run SPS4 92
- Update Software 92
- Run Diagnostics 93
- System Reset 93
- File Utilities 94
- Tutorials 95
- 102 Rockin’ Lead 96
- 40 Classic Comp 96
- C4C3B2A0 C8 97
- 88 Real Vibes 98
- 88 Solo Flute 99
- Module 1 101
- Module 2 101
- Module 3 101
- Module 4 101
- Zone 4 Zone 3 Zone 2 Zone 1 102
- C4C3 E4 F4 B5 C6 G7B2E1 102
- Module 3 Module 2 Module 1 102
- Other Tutorials 105
- Restoring Factory Defaults 106
- Troubleshooting 107
- Audio Problems 109
- MIDI Problems 110
- Sleeve Ring Tip 111
- Left Pedal Right Pedal 111
- If None of the Above 112
- Service Centers 113
- Diagnostics 113
- MIDI Implementation 115
- Physical Specications 117
Related products and manuals for MIDI keyboards Kurzweil SPS4-8
MIDI keyboards Kurzweil PC3K8 Specifications
(425 pages)
(425 pages)
MIDI keyboards Kurzweil SP5-8 Specifications
(126 pages)
(126 pages)
MIDI keyboards Kurzweil PC3LE8 Specifications
(379 pages)
(379 pages)
© 2020, manymanuals.com. All rights reserved. | 1.361 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals